7.5
HIGH CVSS 3.1
CVE-2026-90591
NXP ENET-QOS Ethernet driver re-arms RX descriptors with a clobbered DMA buffer address on packet drop
Description

The NXP ENET-QOS Ethernet driver's receive work handler eth_nxp_enet_qos_rx() in drivers/ethernet/eth_nxp_enet_qos hands each processed descriptor back to the DMA by writing desc->read.control = rx_desc_refresh_flags, which sets OWN_FLAG and BUF1_ADDR_VALID_FLAG. RDES0 of a receive descriptor is the DMA buffer address in read format, but the hardware write-back aliases that word with the VLAN tag fields (or, for a context descriptor, the timestamp low word), so it is destroyed on every completion. The success path rewrites desc->read.buf1_addr before re-arming; the four drop paths — errored or non-first descriptor, net_pkt_rx_alloc() failure, invalid descriptor length, and net_pkt_get_frag() failure — did not, re-arming the ring slot with the write-back residue as its DMA target address. The drop paths are driven entirely by received traffic and need no privilege or special configuration. With the defaults for this driver (CONFIG_NET_BUF_DATA_SIZE of 128 and 16 receive descriptors) a single full-size frame consumes twelve ring slots and twelve K_NO_WAIT fragment allocations, so a short burst of frames sent to the device exhausts the receive pools and reaches the allocation-failure paths; a frame with a receive error, or any frame whose first descriptor was already dropped, reaches the non-first-descriptor path. Once a slot has been poisoned, the DMA writes the next frame received in that slot to an address derived from the frame's VLAN tag fields rather than to a receive buffer. On the supported MCX SoCs that address falls in flash or reserved space, so the transfer raises a fatal bus error that the driver only logs — there is no reset or recovery path — and reception stops permanently until the device is rebooted; where the write is silently discarded instead, the untouched buffer is later handed to the network stack with a length, delivering stale buffer contents as if they were a received frame. A single triggering event is enough to make the condition persistent, so an attacker able to send traffic to the device can permanently disable its network interface.

INFO

Published Date :

Nov. 9, 2026, 10:04 p.m.

Last Modified :

Nov. 9, 2026, 10:04 p.m.

Remotely Exploit :

Yes !

Source :

zephyr
Affected Products

The following products are affected by CVE-2026-90591 vulnerability. Even if cvefeed.io is aware of the exact versions of the products that are affected, the information is not represented in the table below.

ID Vendor Product Action
1 Zephyrproject zephyr
2 Zephyrproject zephyr
CVSS Scores
The Common Vulnerability Scoring System is a standardized framework for assessing the severity of vulnerabilities in software and systems. We collect and displays CVSS scores from various sources for each CVE.
Score Version Severity Vector Exploitability Score Impact Score Source
CVSS 3.1 HIGH e2e69745-5e70-4e92-8431-deb5529a81ad
CVSS 3.1 HIGH MITRE-CVE
Solution
Fix descriptor handling in the NXP ENET-QOS driver to prevent memory corruption and denial of service.
  • Ensure receive descriptors are correctly re-armed.
  • Validate DMA buffer addresses before re-arming.
  • Implement robust error handling for descriptor processing.
  • Update the driver to fix memory corruption vulnerabilities.

We scan GitHub repositories to detect new proof-of-concept exploits. Following list is a collection of public exploits and proof-of-concepts, which have been published on GitHub (sorted by the most recently updated).

Results are limited to the first 15 repositories due to potential performance issues.

The following list is the news that have been mention CVE-2026-90591 vulnerability anywhere in the article.

EPSS is a daily estimate of the probability of exploitation activity being observed over the next 30 days. Following chart shows the EPSS score history of the vulnerability.